High Performance Combined AM/FM Radio Antennas

The original the best and the most copied antennas in Australia

 Designing and Manufacturing AM / FM Antennas since 1979. Infonformation

Its has been our experience that AM / FM antennas in cars are woeful, so it was in 1979 that we designed the M2W & M3W AM/FM antennas
The increase in performance that these antennas have, is not only due to the antenna but more importantly due to the special Cable we use,
The cable MUST be the right kind as well as any patch lead that is attached, in order to get the very best performance.
I
t is very important to make sure that your coax cable is NOT RG58,RG6 or RG59 - if it is,
then you are not getting any where near the best results on AM! especially



M4W   m1p


Item Length Description of the M4W
Price





1







car
285mm
11"

Code : M4W
The M4W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz Originally designed for Buses, where a longer antenna was not possible, It is important to keep in mind that the longer the antenna the better its performance, but there are situations that cannot be avoided, so we have the best performing AM/FM antenna for its short length that can be made.

The M4W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - Very short antenna suitable for all mounting positions on vehicles.
Cons - Performance is very limited due to very short length, Only where a longer antenna is not possible.
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M4P
The M4W antenna with a APN16 - 1.6m long Base cable & Plug        m1p     apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M4P3
The M4W antenna with a APN3 - 3m long Base cable & Plug            m1p      apn16

$54.00

Code : M4P4
The M4W antenna with a APN4 - 4m long Base cable & Plug            m1p      apn16

$56.00

Code : M4P5
The M4W antenna with a APN5 - 5m long Base cable & Plug            m1p       apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not advisable to use a Spring with the M4W
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
 

For Bull Bar Mounting - It is not recommended that you use a spring with the M4W, as it is simply too short.

 

M4WT   m1p
Item Length Description of the M4WT
Price





2




car
285mm
11"

Code : M4WT
The M4WT is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz Originally designed for Trains, where a longer antenna was not possible, It is important to keep in mind that the longer the antenna the better its performance, but there are situations that cannot be avoided, so we have the best performing AM/FM antenna for its short length that can be made.

The M4WT is a hollow 16mm fiberglass antenna that is also available in White, RED or BLUE

Pros  - Very short heavy duty antenna suitable for all mounting positions on vehicles.
Cons - Performance is very limited due to very short length, Originally designed for Trains, Buses etc.
Note - As with all AM/FM antennas it is important that the Cable be the correct type and not RG58 CB coax

$25.00

Code : M4WTP
The M4WT antenna with a APN16 - 1.6m long Base cable & Plug      m1p     apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M4WTP3
The M4WT antenna with a APN5 - 5m long Base cable & Plug           m1p     apn16

$54.00

Code : M4WTP4
The M4WT antenna with a APN4 - 4m long Base cable & Plug          m1p     apn16

$56.00

Code : M4WTP5 
The M4WT antenna with a APN5 - 5m long Base cable & Plug         m1p     apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not advisable to use a Spring with the M4WT, it is simply too short
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.


BMB
Bonnet Mount

$35.00
 

For Bull Bar Mounting - It is not recommended that you use a spring with the M4W, as it is simply too short.

 

M7W   m1p
Item Length Description of the M7W
Price






3






car
590mm
23"

Code : M7W
The M7W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz, This is the shortest antenna that is recommended on a vehicle, It performs better than the M4W and M4WT but a longer antenna will work better, Using a spring with this antenna is not needed and it will not affect its performance.

The M7W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - Short antenna suitable for all mounting positions on vehicles.
Cons - Performance is limited due to its short length
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M7P
The M7W antenna with a APN16 1.6m Base & Cable & Plug  m1p    apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M7P3
The M7W antenna with a APN3 - 3m long Base cable & Plug    m1p    apn16

$54.00

Code : M7P4
The M7W antenna with a APN4 - 4m long Base cable & Plug    m1p    apn16

$56.00

Code : M7P5
The M7W antenna with a APN5 - 5m long Base cable & Plug    m1p    apn16

For other cable lengths please see our Bases and Cables section

 

$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
sao
SAL Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAL spring under the antenna absorbs the vibration from the engine and saves the antenna from eventually failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.


If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAL mount to be an excellent choice, click on the image on the left.


SAL
Light Spring

$30.00

M3W  m1p
Item Length Description of the M3W
Price






4




car
840mm
33"

Code : M3W

The M3W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz. The M3W is the best all round performing antenna

The M3W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - Excellent performing short antenna suitable for all mounting positions on vehicles.
Cons - I could not think of any
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M3P
The M3W antenna plus a APN16 - 1.6m long Base & Cable   m1p     apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M3P3
The M3W antenna plus a APN3 - 3m long Base cable & Plug  m1p     apn16 

$54.00

Code : M3P4
The M3W antenna plus a APN4 - 4m long Base cable & Plug  m1p     apn16

$56.00

Code : M3P5
The M3W antenna plus a APN5 - 5m long Base cable & Plug  m1p      apn16

For other cable lengths please see our Bases and Cables section

 

$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.


BMB
Bonnet Mount

$35.00
sao
SAL Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAL spring under the antenna absorbs the vibration from the engine and saves the antenna from eventual failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.

If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAL mount to be an excellent choice, click on the image on the left.

SAL
Light Spring

$30.00

M6W   m1p
Item Length Description of the M6W
Price





5




car
1040mm
41"

Code : M6W
The M6W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz. The M6W is a great all round performing antenna, only the M2W outperforms this antenna, The M6W is 7mm thick and at 1040mm long will sit perfectly onto any bonnet of a vehicle without touching the ceiling of any carparks.

The M6W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - Excellent performing short antenna suitable for all mounting positions on vehicles.
Cons - I could not think of any
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M6P
The M6W antenna with a APN16 - 1.6m long Base & Cable        m1p    apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M6P3
The M6W antenna with a APN3 - 3m long Base cable & Plug      m1p    apn16

$54.00

Code : M6P4
The M6W antenna with a APN4 - 4m long Base cable & Plug      m1p    apn16

$56.00

Code : M6P5
The M6W antenna with a APN5 - 5m long Base cable & Plug      m1p    apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
sao
SAO Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAO spring under the antenna absorbs the vibration from the engine and saves the antenna from eventually failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.


If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAO mount to be an excellent choice, click on the image on the left.

SAO
Heavy Spring

$35.00

M5W   m1p
Item Length Description of the M5W
Price





6





car
1200mm
47"

Code : M5W
The M5W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz, and is a popular choice due to its great performance and not too long length, This is a great choice for bull bar mounting together with the SAO spring as it is just the right length not to crash into obstacles.

The M5W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - Excellent performing short antenna suitable for all mounting positions on vehicles.
Cons - I could not think of any
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M5P
The M5W antenna with a APN16 - 1.6m long Base & Cable    m1p     apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M5P3
The M5W antenna with a APN3 - 3m long Base cable & Plug   m1p     apn16

$54.00

Code : M5P4
The M5W antenna with a APN4 - 4m long Base cable & Plug   m1p     apn16

$56.00

Code : M5P5
The M5W antenna with a APN5 - 5m long Base cable & Plug   m1p      apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
sao
SAO Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAO spring under the antenna absorbs the vibration from the engine and saves the antenna from eventually failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.


If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAO mount to be an excellent choice, click on the image on the left.

SAO
Heavy Spring

$35.00
Order Here


M2W   m2w

best

Item Length Description of the M2W
Price





7







car
1520mm
60"

Code : M2W
The M2W is an antenna designed for receiving AM & FM frequencies of MW 525 kHz to 1705 kHz and FM 88 to 108 MHz. This is the best performing AM / FM antenna and is guaranteed to improve the performance of you radio as long as it is combined with the correct Base and Cable. The M2W is centered on 96MHz with a gain of 2dBi.

The M2W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW

Pros  - This enhances the FM signals nicely.
Cons - Too long for most folks use but put on the right hand side of a bonnet its awesome
Note - As with all AM/FM antennas it is important that the Base and Cable be the correct type and not RG58 CB coax

$25.00

Code : M2P
The M2W antenna with a APN16 - 1.6m long Base & Cable    m1p    apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M2P3
The M2W antenna with a APN3 - 3m long Base cable & Plug   m1p    apn16

$54.00

Code : M2P4
The M2W antenna with a APN4 - 4m long Base cable & Plug   m1p    apn16

$56.00

Code : M2P5
The M2W antenna with a APN5 - 5m long Base cable & Plug  m1p    apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
sao
SAO Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAO spring under the antenna absorbs the vibration from the engine and saves the antenna from eventually failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.

If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAO mount to be an excellent choice, click on the image on the left.

SAO
Heavy Spring

$35.00

 

High Performance AM & Shortwave Radio Antenna up arrow


M1W    m1p

AM Only Antenna for Shortwave and MW broadcast band from 525 kHz to 1705 kHz


Item Length Description of the M1W
Price







8





car
1520mm
60"

Code : M1W

The M1W is an antenna designed for receiving AM & Shortwave frequencies only i.e.: 525kHz to 21MHz,
It can be cut down to what ever length that is required but it is important to note that the longer the antenna the better its performance. The M1W is a 7mm thick fiberglass antenna that has a tight loading coil from the top to bottom which creates a sensitive antenna for very low frequencies.

The M1W is a 7mm thick fiberglass antenna that is also available in White, RED, GREEN, BLUE or YELLOW
                       The M1W will work on FM, but not as well, as a combined AM / FM antenna

Note - This antenna is designed to work only with a low capacitance cable RG62 or equivalent not CB radio coax 
Pros  - Combined with the APN16 , this is the best performing AM antenna on the market.
Cons - It is long and top heavy, it may need a heavy duty spring if on a high vibration installation

NOTE: The M1W can be cut to any length without too much reduction in performance

$25.00

Code : M1P
The M1W antenna with a APN16 - 1.6mtr long Base & Cable   m1p    apn16
Perfect for mounting onto the bonnet of any vehicle via a Z bracket or a BMB mount, a spring is not required

$50.00

Code : M1P3
The M1W antenna with a APN3 - 3mtr long Base cable & Plug   m1p    apn16

$54.00

Code : M1P4
The M1W antenna with a APN4 - 4mtr long Base cable & Plug   m1p    apn16

$56.00

Code : M1P5
The M1W antenna with a APN5 - 5mtr long Base cable & Plug   m1p    apn16

For other cable lengths please see our Bases and Cables section
$60.00

bmb

bmb
BMB

For Bonnet Mounting - It is not necessary to use a Spring, and it will not affect the performance of the antenna!
If you intend to mount this antenna on the bonnet or on the boot of a vehicle then you may find the Mobile One BMB mount to be an excellent choice, See image on the left. The BMB simply slides onto the side or your bonnet and then is held in place by two small grub screws, The BMB is the best bonnet mount for all two way radio, Scanner and AM/FM radio as it places the antenna close to the bonnet, this produces an excellent SWR where transmitting antennas are concerned and an excellent impedance where receiving antennas are concerned, The BMB is strong enough to take antennas up to 2mtrs long.

However the BMB does not fit all vehicles, in this case a Z-Bracket can be used, click on the image on the left.

BMB
Bonnet Mount

$35.00
sao
SAO Spring

For Bull Bar Mounting - It is absolutely necessary to use a Spring!

It is important that when mounting any antenna on a bull bar that you add a spring below it, this is because when the vehicles engine is running it causes vibration and this vibration is then amplified to the front of the vehicle, Adding the SAO spring under the antenna absorbs the vibration from the engine and saves the antenna from eventually failing, Not all vehicles have vibration issues and some have such bad vibration that even with a spring the antenna will eventually fail.

If you intend to mount this antenna on the Bull Bar of a vehicle the you may find the Mobile One SAO mount to be an excellent choice, click on the image on the left.

SAO
Heavy Spring

$35.00