For the 6 Meter Band

Fiberglass 1/4 wave tapered from 6.5mm to 4mm with 5/16" fitting coated with polyolefin black or white. The M6-1 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMS mount (Z brackets are not recommended with this antenna)

Recommended Accessories - UL4BNC or UL4PL with BMB or Mag3.6PL

Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring

Price $59.00 + Pack & Freight $26

For the 144MHz to 148MHz - 2 Meter Band

A 1/4 wave helical antenna with BNC connector, covered entirely with polyolefin rubber heatshrink.

The BNC146 has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna for use on the

entire 2m Band 144MHz to 148MHz.

Note: Also ideal for scanners that are mainly used on the 2 metre band.

Price $29.00 + Pack & Post $10.00

The SMA146 is designed for transceivers where the SMA antenna connector is extended from the case of the transceiver.

A 1/4 wave helical antenna with SMA connector designed especially for exposed SMA connectors on hand held radios and covered entirely with polyolefin rubber heatshrink.

The SMAVAR146 has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna for use on the entire Air Band 144MHz to 148MHz.

Note: The SMAVAR146 has a diameter of 12mm at its base and may not fit some radios that have the SMA connector recessed into the radio, if this is the case then the SMAIVAR146 is the better choice.

Price $25.00 + Pack & Post $10.00

The following Antennas have a 5/16" 26tpi base fitting

As these antennas are all 1/4 wave for the Airband band they need to be mounted so that the bottom of the antenna is as close to the surface of the metal ground plane as possible the very best way is to use a Mobile One UHF base on a BMB mount if on a vehicle

The RDRM146 is a shortened 1/4 Wave antenna that is covered with polyolefin and very easy to tune

The M146 is supplied tuned to 144MHz and can be fine tuned to the desired part of the 2mtr band

Tx Bandwidth = 3MHz, <1.5:1, Rx Bandwidth = 30MHz

Recommended Accessories - UL4BNC or UL4PL with BMB or Mag3.6PL

Price 45.00 + Pack & Post $12.00

A robust 7mm thick antenna made with copper braid to ensure the widest possible bandwith and covered with polyolefin

The M144-1 is a full 1/4 Wave antenna that is covered with polyolefin

The M144-1 is supplied untuned

Tx Bandwidth = 4MHz, Rx Bandwidth = 40MHz

NOTE: Do not use a spring, If you have to, then you will need to retune the antenna

NOTE: Do not use a Z bracket as the antenna will be too high and have a worst SWR, Some gutter mounts will not work well either

Recommended Accessories - UL4BNC or UL4PL with BMB or Mag3.6PL

Price $29.00 + Pack & Post $12.00

The S124-1 is a full 1/4 Wave Stainless Steel antenna

The S124-1 is supplied tuned to the center of the Airband on 124MHz but can be center tuned to your requested frequency

Tx Bandwidth = 5MHz, Rx Bandwidth = 50MHz

NOTE: Do not use a spring, If you have to, then you will need to retune the antenna

NOTE: Do not use a Z bracket as the antenna will be too high and have a worst SWR, Some gutter mounts will not work well either

Recommended Accessories - UL4BNC or UL4PL with BMB or Mag3.6PL

Price $19.00 + Pack & Post $12.00

Stainless steel 1/4 wave antenna suitable for 2m band and high band VHF applications tunable from 108MHz.
This antenna is not pretuned and comes with a cutting chart for customer tuning.

The WPS144 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMB mount. (Z brackets are not recommended with this antenna)

The WPS144 comes with a "UB5PL" 5m long Base and Cable

Recommended Accessories - BMB

Price $59.00 + Pack & Post $16.00

A robust 7mm thick antenna made with copper braid to ensure the widest possible bandwith and covered with polyolefin
The WPM144 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the BMB mount. (Z brackets are not recommended with this antenna)

The WPM144 comes with a "UB5PL" 5m long Base and Cable

Recommended Accessories - BMB

Price $69.00 + Pack & Post $16.00

The M144-3 is a fiberglass 5/8 wave antenna suitable for vehicle and base applications on a 5/16" fitting,

The M144-3 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible
such as the BMS mount (Z brackets are not recommended with this antenna)

Recommended Accessories - UL4PL with BMB or MAG4BNC or equivalent.

Note: You Should NOT use a spring with this antenna.

Note: A M144-3 on a MAG4BNC put on the guttering of the house is an simple solution as a base station antenna.
Note: Also ideal for scanners that are mainly used for Air Band reception.

This antenna is required to be cut-to-tune for the best VSWR on 2mtrs

Price $79.00 + Pack & Freight $26.00

CDB146 - 2m 144~148MHz - Base Antenna Available in black only
 

The CDB146 is a Ground  Inderpendant Coaxial Dipole with 3dbi gain. Providing a broad feed angle and low VSWR across the whole 2 meter band

This product is most suitable for Base Station, Portable or Mobile situations.
The antenna is  supplied with a 500 mm Coaxial pigtail with a FME Male Connector.

A stainless steel 20 mm base tube is provided for mast mounting using worm drive clamps or u bolts.

VSWR = <1.5:1 from 144 - 148 Mhz 

Feed cables of various lengths can be made to suit any feed situation or radio connector types.

Price $150.00 + Pack & Freight $26.00

Connectors, Clamps, and Cables to suit the above base Antennas

We can also special length cables with whatever connectors you may require!

UHF 430MHz 70cm Band

As these antennas are all 1/4 wave for the UHF 70cm Band, they need to be mounted so that the bottom of the antenna is as close to the surface of the metal ground plane as possible

the very best way is to use a Mobile One UHF base on a BMB mount

NOTE: Do not use a Z bracket as the antenna will be too high and have a worst SWR, Some gutter mounts will not work well either

Recommended Accessories - UL4BNC or UB4PL with BMB or Mag3.6PL

Price $29.00 + Pack & Post $12.00

As these antennas are all 1/4 wave for the UHF 70cm Band, they need to be mounted so that the bottom of the antenna is as close to the surface of the metal ground plane as possible

the very best way is to use a Mobile One UHF base on a BMB mount

NOTE: Do not use a Z bracket as the antenna will be too high and have a worst SWR, Some gutter mounts will not work well either

Recommended Accessories - UL4BNC or UB4PL with BMB or Mag3.6PL

Price $19.00 + Pack & Post $12.00

Note: this antenna is PRE-TUNED for 430mhz band.  Antenna UHF collinear fiberglass covered with PVC 4.5dB gain

Recommended Accessories - UL4BNC or UL4C with BMB or Mag3.6C
Note: You can NOT use a spring with this antenna.

Price $39.00 + Pack & Post $16.00

2m & 70cm Dual Band Antenna

M270 

Antenna UHF collinear fiberglass covered with PVC 4.5dB gain on UHF Unity gain on 2m

Note: You can NOT use a spring with this antenna. Note: this antenna is PRE-TUNED for 430mhz band BUT is CUT-TO-TUNE for 144mhz band. (Cut 1mm at a time using a VSWR bridge)

Note: The M270 needs a small ground plane area and should be mounted close to the ground plane, do not use a z bracket as the z bracket will cause a untuned dipole effect on UHF you should use a BMS

The best mounting is on the front bonnet of the car on a BMS.

Pros  - Combine 2m & 70cm bands in one
Cons - Using separate antennas will provide a much better result.

Recommended Accessories - UL4BNC or UL4C with BMB or Mag3.6C

This antenna is required to be cut-to-tune for the best VSWR on 2mtrs

Price $59.00 + Pack & Post $16.00