All Mobileone Antennas

180MHz to 400MHz

The following antennas are sorted by the frequency that they are designed for!
Example : 180MHz to 400MHz means that particular antenna can be made anywhere within that range
but not that the antenna will transmit over that entire range as this is impossible for a transmitting antenna.
BNC+freqbncvar
Length Description of the BNC+freq 180MHz ~ 400MHz
210mm
8"

A 1/4 wave helical antenna with BNC connector, covered entirely with polyolefin rubber heatshrink. The BNCVAR has a specially made 1/4λ phosphor bronze helical coil tuned to produce a low SWR and an exceptionally broadband antenna

The BNCVAR can be supplied tuned to any frequency from 180 to 400MHz simply ask or you can order on line with the code "BNCVAR" followed with the frequency required eg: BNCVAR163 for 163MHz

 

Note: This antenna can be supplied as a TNC or N connector or any colour

Note: Also ideal for scanners that are mainly used on High band VHF.

sma

SMA+freq
Length Description of the SMA+freq 180MHz ~ 400MHz
210mm
8"

The SMA+freq is designed for transceivers where the SMA antenna connector is extended from the case of the transceiver.

The SMAVAR can be supplied tuned to any frequency from 180MHz to 400MHz simply ask or you can order on line with the code "BNC" followed with the frequency required eg: SMA163 for 163MHz.

A 1/4 wave helical antenna with SMA connector designed especially for exposed SMA connectors on hand held radios and covered entirely with polyolefin rubber heatshrink. The SMA has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna.

 

Note: Also ideal for scanners that are mainly used for 2m band.

 

NOTE: This antenna may not fit neatly onto your transceiver


Note: The SMA has a diameter of 12mm at its base and may not fit some radios that have the SMA connector recessed into the radio, if this is the case then the SMAIVAR is the better choice.

SMAI+freq
Length Description of the SMAI+freq 180MHz ~ 400MHz
210mm
8"

The SMAI is designed for transceivers where the SMA antenna connector is recessed into the case of the transceiver.

The SMAI can be supplied tuned to any frequency from 180MHz to 400MHz simply ask or you can order on line with the code "BNC" followed with the frequency required eg: SMAIVAR163 for 163MHz.

A 1/4 wave helical antenna with SMA connector designed especially for recessed SMA connectors on hand held radios and covered entirely with polyolefin rubber heatshrink. The SMAI has a specially made 1/4λ phosphor bronze helical coil tuned to produce an exceptionally broadband antenna.

 

Note: Also ideal for scanners that are mainly used for 2m band.


Note: The SMAIVAR172 will fit all hand held radios and scanners that have a SMA connection.


SW2   sw2
Length Description of the SW2
630mm
25"

Tuned length
depends on
the frequency

Stainless steel 1/4 wave antenna can be tuned from 108MHz upward to 500MHz.

This antenna is not pretuned and comes with a cutting chart for customer tuning.

The SW2 works best when mounted onto a bracket that is as close to the surface of the ground plane as possible such as the Mobile One BMB mount. (Z brackets are not recommended with this antenna)


This antenna is available for tuned for frequencies from 160MHz to 180MHz state the tx frequency range required


Pros  - Stainless Steel

Cons  - Not as broadband as the M172-1 (see below)

Recommended Accessories - UL3.6C with BMB or Mag3.6C. Z Bracket is not recommended
Note: You can use a spring SAL or SAO but the antenna will need to be re-tuned on the spring



Code : SWP
The SW2 antenna with the UL3.6C Base cable & Plug as a pack    swp

Code : SWPBNC
The SW2 antenna with the UL3.6BNC Base cable & Plug as a pack    swp